TP29 A portable tank having a minimum test pressure of 1.5 bar (150.0 kPa) may be used provided the calculated test pressure is 1.5 bar or less based on the MAWP of the hazardous materials, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. (h) Column 7: Special provisions. A2 Single packagings are not permitted on aircraft. 139 Use of the special arrangement proper shipping names for international shipments must be made under an IAEA Certificate of Competent Authority issued by the Associate Administrator in accordance with the requirements in 173.471, 173.472, or 173.473 of this subchapter. Each inner packaging contains not more than 30 mL; b. [Amdt. (6) The rate of oxygen release from the outer packaging does not exceed 15 mL per hour. B61 Written procedures covering details of tank car appurtenances, dome fittings, safety devices, and marking, loading, handling, inspection, and testing practices must be approved by the Associate Administrator before any single unit tank car tank is offered for transportation. 107 The classification of the substance is expected to vary especially with the particle size and packaging but the border lines have not been experimentally determined; appropriate classifications should be verified following the test procedures in 173.57 and 173.58 of this subchapter. Only Specifications MC 304, MC 307 or DOT 407 cargo tank motor vehicles are authorized for transportation by vessel. Be ASME Code (U) stamped for 100% radiography of all pressure-retaining welds; b. Authorized specification bulk outer packagings are UN11G fiberboard intermediate bulk containers (IBC) and UN13H4 woven plastic, coated and with liner flexible intermediate bulk containers (FIBCs) meeting the Packing Group II performance level and lined with a plastic liner of at least 6 mil thickness. TP26 The heating device must be exterior to the shell. f. Flexible: 13H2, 13H3, 13H4, 13H5, 13L2, 13L3, 13L4, 13M1 and 13M2 (flexible IBCs must be sift-proof and water resistant or must be fitted with a sift-proof and water resistant liner). B45 Each tank must have a reclosing combination pressure relief device equipped with stainless steel or platinum rupture discs approved by the AAR Tank Car Committee. The map below, compiled from data provided by the Federal Emergency Management Agency (FEMA), is the most accurate nuclear attack map and fallout demonstration available for 2023: (Image courtesy of FEMA and Halcyon Maps) The fallout would rapidly spread, turning targeted cities into whole affected regions. For this test, the provisions of paragraphs 16.6.1.2 except letter g, 16.6.1.3.1 to 16.6.1.3.6, 16.6.1.3.7(b) and 16.6.1.3.8 of the UN Manual of Tests and Criteria must be applied. B133 Hydrochloric acid concentration not exceeding 38%, in Packing Group II, is authorized to be packaged in UN31H1 or UN31HH1 intermediate bulk containers when loaded in accordance with the requirements of 173.35(h) of this subchapter. 65 The group of alkaline earth metals includes magnesium, calcium, strontium, and barium. Lighter refills offered for transportation under this entry may not exceed 4 fluid ounces capacity (7.22 cubic inches) or contain more than 65 grams of fuel. 441 For marine pollutants transported under UN3077, Environmentally hazardous substance, solid, n.o.s. or UN3082, Environmentally hazardous substance, liquid, n.o.s. and for purposes of shipping paper and package marking requirements, the technical name used in association with the basic description may be a proper shipping name listed in the 172.101 Hazardous Material Table; provided that the name chosen is not also an entry that includes n.o.s. as a part of the name or one that has a G in column (1) of the table. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter. B59 Water-tight, sift-proof, closed-top, metal-covered hopper cars are also authorized provided that the lading is covered with a nitrogen blanket. The Associate Administrator will base the authorization on results from Series 2 tests and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport in accordance with the requirements of this subchapter. 166 When transported in non-friable tablet form, calcium hypochlorite, dry, may be transported as a Packing Group III material. A37 This entry applies only to a material meeting the definition in 171.8 of this subchapter for self-defense spray. Where different hazardous materials in limited quantities are packed together in the same outer packaging, when a gross mass is indicated Column 4 of 173.27 Table 3, the net quantity of each hazardous material must be shown in addition to the gross mass of the completed package. Molten sulfur must be marked as required by 172.325 of this subchapter. If a tank car tank is equipped with a non-reclosing pressure relief device, the rupture disc must be perforated with a 3.2 mm (0.13 inch) diameter hole. 160 This entry applies to safety devices for vehicles, vessels or aircraft, e.g. (3) When no bottom openings are authorized, the alternative portable tank must not have bottom openings. For transportation by aircraft, a telephone report in accordance with 171.15(a) is required if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a dry battery. When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. B11 Tank car tanks must have a test pressure of at least 2,068.5 kPa (300 psig). 164 Substances must not be transported under this entry unless approved by the Associate Administrator on the basis of the results of appropriate tests according to Part I of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). 357 A bulk packaging that emits hydrogen sulfide in sufficient concentration that vapors evolved from the crude oil can present an inhalation hazard must be marked as specified in 172.327 of this part. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. The caps must not contain more than an average of twenty-five hundredths of a grain of explosive composition per cap; c. The caps must be packed inside packagings constructed of cardboard not less than 0.013-inch in thickness, metal not less than 0.008-inch in thickness, non-combustible plastic not less than 0.015-inch in thickness, or a composite blister package consisting of cardboard not less than 0.013-inch in thickness and non-combustible plastic not less than 0.005-inch in thickness that completely encloses the caps; d. The minimum dimensions of each side and each end of the cardboard packaging must be 1/8th inch in height or more; e. The number of caps inside each packaging must be limited so that not more than 10 grains of explosives composition may be packed into one cubic inch of space, and not more than 17.5 grains of the explosive composition of toy caps may be packed in any inner packaging; f. Inner packagings must be packed in outer packagings meeting PG II performance criteria; g. Toy caps may be packed with non-explosive or non-flammable articles provided the outer packagings are marked as prescribed in this paragraph; h. Toy paper caps of any kind must not be packed in the same packaging with fireworks; i. Packages containing mixtures with not less than 90% by mass, of phlegmatizer need not bear a POISON subsidiary risk label. 79 This entry may not be used for mixtures that meet the definition for oxidizing gas. Each radiation detector must meet the following conditions: (1) The pressure in each neutron radiation detector must not exceed 105 kPa absolute at 20 C (68 F); (2) The amount of gas must not exceed 13 grams (0.45 ounces) per detector; and, (3) Each neutron radiation detector must be of welded metal construction with brazed metal to ceramic feed through assemblies. 12 In concentrations greater than 40 percent, this material has strong oxidizing properties and is capable of starting fires in contact with combustible materials. B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. Subscribe to: Changes in Title 49 :: Subtitle B :: Chapter I :: Subchapter C :: Part 172 :: Subpart B :: Section 172.102. N91 The use of a non specification sift-proof, non-bulk, metal can with or without lid, or a non specification sift-proof, non-bulk fiber drum, with or without lid is authorized when transporting coal tar pitch compounds by motor vehicle or rail freight. N42 1A1 drums made of carbon steel with thickness of body and heads of not less than 1.3 mm (0.050 inch) and with a corrosion-resistant phenolic lining are authorized for stabilized benzyl chloride if tested and certified to the Packing Group I performance level at a specific gravity of not less than 1.8. 336 The use of UN1H1 drums, UN3H1 jerricans, and UN6HA1 composite packagings which meet the requirements of part 178 of the HMR at the Packing Group I or II performance level. Lead compounds which, when mixed in a ratio of 1:1,000 with 0.07 M (Molar concentration) hydrochloric acid and stirred for one hour at a temperature of 23 C 2 C, exhibit a solubility of 5% or less are not subject to the requirements of this subchapter unless they meet criteria as another hazard class or division. j. (TOY CAPS) - HANDLE CAREFULLY OR TOY CAPS - HANDLE CAREFULLY; and. (8) A code containing the letters TP refers to a portable tank special provision for UN or IM Specification portable tanks that is in addition to those provided by the portable tank instructions or the requirements in part 178 of this subchapter. Fertilizers meeting the criteria for this identification number are only subject to the requirements of this subchapter when offered for transportation and transported by air or vessel. (2) A code containing the letter A refers to a special provision which applies only to transportation by aircraft. 22 If the hazardous material is in dispersion in organic liquid, the organic liquid must have a flash point above 50 C (122 F). Openings for safety relief devices on multi-unit tank car tanks shall be plugged or blank flanged. (ii) One bottle for every two hours of production, or for every 2,500 bottles produced, must be tested by dropping a bottle filled to 98 percent capacity with water from a height of 1.2 meters (3.9 feet) onto solid concrete directly on the closure. 4 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone D (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. Tables 1, 2, and 3 follow: 1 Flexible plastic (51H) Large Packagings are only authorized for use with flexible inner packagings. A13 Bulk packagings are not authorized for transportation by aircraft. 24 Alcoholic beverages containing more than 70 percent alcohol by volume must be transported as materials in Packing Group II. a. Mixtures of one or more organic lead mixtures (such as tetraethyl lead, triethylmethyl lead, diethyldimethyl lead, ethyltrimethyl lead, and tetramethyl lead) with one or more halogen compounds (such as ethylene dibromide and ethylene dichloride), hydrocarbon solvents or other equally efficient stabilizers; or. These mixtures may be classified in Division 4.1 when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) and approved by the Associate Administrator. B65 Tank cars constructed before March 16, 2009, must have a test pressure of 34.47 Bar (500 psig) or greater and conform to Class 105A. A101 In addition to the applicable requirements of 173.185, the quantity of lithium metal in the batteries contained in any piece of equipment must not exceed 12 g per cell and 500 g per battery. B57 Class 115A tank car tanks used to transport chloroprene must be equipped with a non-reclosing pressure relief device of a diameter not less than 305 mm (12 inches) with a maximum rupture disc pressure of 310 kPa (45 psig). This content is from the eCFR and may include recent changes applied to the CFR. b. 157 When transported as a limited quantity or a consumer commodity, the maximum net capacity specified in 173.151(b)(1)(i) of this subchapter for inner packagings may be increased to 5 kg (11 pounds). Date of the visual inspection must be stenciled on the tank near the other required markings. full text search results In addition to the provisions applicable to the transport of Division 6.1 substances, the provisions of 173.421(c) and 173.443(a) of this subchapter apply. TP21 The wall thickness must not be less than 8 mm. 138 This entry applies to lead compounds which, when mixed in a ratio of 1:1,000 with 0.07 M (Molar concentration) hydrochloric acid and stirred for one hour at a temperature of 23 C 2 C, exhibit a solubility of more than 5%. Do not enter until vapors have dissipated. The driver of the transport vehicle and the consignee(s) must be trained not to enter the transport vehicle until the ammonia vapors have dissipated, and the emergency response information on the shipping paper must indicate that the vehicle contains ammonia vapors. b. Such packages must be transported on cargo aircraft only. TP13 Self-contained breathing apparatus must be provided when this hazardous material is transported by sea. 52 This entry may only be used for substances that are too insensitive for acceptance into Class 1 (explosive) when tested in accordance with Test Series 2 in the UN Manual of Tests and Criteria, Part I (incorporated by reference; see 171.7 of this subchapter). B30 MC 312, MC 330, MC 331 and DOT 412 cargo tanks and DOT 51 portable tanks must be made of stainless steel, except that steel other than stainless steel may be used in accordance with the provisions of 173.24b(b) of this subchapter. Transport vehicles must be vented to prevent accumulation of vapors at a poisonous or flammable concentration. (In the example, the special provision codes for toluene are IB2, T4 and TP1.) Microsoft Edge, Google Chrome, Mozilla Firefox, or Safari. 155 Fish meal, fish scrap and krill meal may not be transported if the temperature at the time of loading either exceeds 35 C (95 F), or exceeds 5 C (41 F) above the ambient temperature, whichever is higher. 362 This entry applies to liquids, pastes or powders, pressurized with a propellant that meets the definition of a gas in 173.115. (9) W codes. Column 1 uses six symbols to identify hazardous materials with special shipping conditions such as restrictions for air, domestic, international, or water vessel transport. IBCs must be packed in closed freight containers or a closed transport vehicle. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. Dry sodium cyanide or potassium cyanide is also permitted in siftproof, water-resistant, fiberboard IBCs when transported in closed freight containers or transport vehicles. TP3 The maximum degree of filling (in %) for solids transported above their melting points and for elevated temperature liquids shall be determined by the following: Where: df and dr are the mean densities of the liquid at the mean temperature of the liquid during filling and the maximum mean bulk temperature during transport respectively. 109 Rocket motors must be nonpropulsive in transportation unless approved in accordance with 173.56 of this subchapter. For Federal Register citations affecting 172.102, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www.govinfo.gov. The packaging shall be designed for a working temperature of at least 121 C (250 F). (2) An indication of compliance with this special provision must be provided by marking each package with the words not restricted or by including the words not restricted on a transport document such as an air waybill accompanying the shipment. Pressure relief devices shall be designed to prevent the entry of foreign matter, the leakage of liquid and the development of any dangerous excess pressure. Each transport unit must be leakproof when used as bulk packaging. (ii) The following table specifies the portable tank requirements applicable to T Codes T1 through T22. For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). c. Self-propelled vehicles or equipment that also contain an internal combustion engine must be described using the entries Engine, internal combustion, flammable gas powered or Engine, internal combustion, flammable liquid powered or Vehicle, flammable gas powered or Vehicle, flammable liquid powered, as appropriate. These provisions apply only to transportation by aircraft: A1 Single packagings are not permitted on passenger aircraft. Column 7 specifies codes for special provisions applicable to hazardous materials. This entry applies to machinery or apparatus containing hazardous materials as a residue or as an integral element of the machinery or apparatus. Primary receptacles must conform to the general packaging requirements of subpart B of part 173 of this subchapter and may not leak. Table I - Maximum Ambient Temperature - Gasoline. 43 The membrane filters, including paper separators and coating or backing materials, that are present in transport, must not be able to propagate a detonation as tested by one of the tests described in the UN Manual of Tests and Criteria, Part I, Test series 1(a) (IBR, see 171.7 of this subchapter). Flammable components are flammable liquids and liquid mixtures, flammable solids and solid mixtures or flammable gases and gas mixtures meeting the following criteria: (1) A flammable liquid is a liquid having a flashpoint of not more than 93 C (200 F); (2) A flammable solid is a solid that meets the criteria in 173.124 of this subchapter; or. TP7 The vapor space must be purged of air by nitrogen or other means. B3 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks and DOT 57 portable tanks are not authorized. The rechargeable lithium ion cells can only be charged from the primary lithium metal cells; ii. These provisions apply only to bulk packagings. These special provisions are in addition to the standard packaging requirements. If a package contains both lithium metal batteries and lithium ion batteries packed with and contained in equipment, then the shipping paper must indicate both UN 3091 Lithium metal batteries packed with equipment and UN 3481 Lithium ion batteries packed with equipment.. 51 This description applies to items previously described as Toy propellant devices, Class C and includes reloadable kits. TP16 The portable tank must be protected against over and under pressurization which may be experienced during transportation. 136 This entry applies only to articles, machinery, and apparatus containing hazardous materials as an integral element of the article, machinery, or apparatus. A single packaging of a 4C2 sift-proof, natural wood box; or. 134 This entry applies only to vehicles powered by wet batteries, sodium batteries, lithium metal batteries or lithium ion batteries, and equipment powered by wet batteries or sodium batteries that are transported with these batteries installed. This includes vehicles transported in a packaging. W8 Vessel stowage category for pyrophoric thorium metal or pyrophoric uranium metal is D as defined in 172.101(k)(4). Essentially, such SSolder complies with RoHS (Restriction of Hazardous Substances) regulations. Specification 110A500W tanks must be stainless steel. 132 This description may only be used for ammonium nitrate-based compound fertilizers. The chemical under pressure must be classed based on the hazard characteristics of the components in the propellant; the liquid; or the solid. The total mass of lithium batteries contained in any package must not exceed the quantity limits in columns (9A) and (9B) for passenger aircraft or cargo aircraft, as applicable; b. This entry may not be used for ammonium nitrate for which a proper shipping name already exists in the 172.101 Hazardous Materials Table, including ammonium nitrate mixed with fuel oil or any other commercial grade of ammonium nitrate (e.g., ammonium nitrate fertilizer). However, button cell batteries installed in equipment (including circuit boards) need not be considered; and, c. The shipping paper must indicate UN 3091 Lithium metal batteries packed with equipment or UN 3481 Lithium ion batteries packed with equipment, as appropriate. If a frangible disc is required in series with the reclosing pressure relief device for the specified portable tank, the alternative portable tank must be fitted with a frangible disc in series with the reclosing pressure relief device; and, (1) When two effective means are specified, the alternative portable tank is fitted with bottom openings having two or three effective means of closure or no bottom openings; or, (2) When three effective means are specified, the portable tank has no bottom openings or three effective means of closure; or. that, for example, are used for medical, analytical, diagnostic, testing, or repair purposes. 181 When a package contains a combination of lithium batteries contained in equipment and lithium batteries packed with equipment, the following requirements apply: a. For all modes of transportation, a written report submitted, retained, and updated in accordance with 171.16 is required if a fire, violent rupture, explosion or dangerous evolution of heat occurs as a direct result of a dry battery or battery-powered device. Company Name: Artisan EHS Consulting, LLC. Column 8 The proper shipping name Paint related material may be used for consignments of packages containing Paint and Paint related material in the same package; b. 170 Air must be eliminated from the vapor space by nitrogen or other means. 142 These hazardous materials may not be classified and transported unless authorized by the Associate Administrator. Equipment powered by lithium metal batteries or lithium ion batteries must be described using the entries Lithium metal batteries contained in equipment or Lithium metal batteries packed with equipment or Lithium ion batteries contained in equipment or Lithium ion batteries packed with equipment, as appropriate. 13 The words Inhalation Hazard shall be entered on each shipping paper in association with the shipping description, shall be marked on each non-bulk package in association with the proper shipping name and identification number, and shall be marked on two opposing sides of each bulk package. N75 Packages consisting of tightly closed inner packagings of glass, earthenware or metal, securely cushioned and packed in outer wooden barrels or wooden or fiberboard boxes, capacity not over 2.5 kg (5.5 pounds) net weight, are authorized and need not conform to the requirements of part 178 of this subchapter. B116 The use of non specification, sift-proof dump or hopper type vehicles, and sift-proof roll-on/roll-off bulk bins, which must be covered by a tarpaulin, metal cover, or equivalent means is authorized for the transportation of spent bleaching earth by motor vehicle.
column 7 of the hazardous materials table